新闻中心

News

Numerical control cutting process of thread

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2021-06-23
  • Views:0

(Summary description)The thread cutting process depends on the structure of the machined parts and the CNC machine tool used. Generally speaking, using the right cutting edge to process right-handed threads and using the left cutting edge to process left-handed threads has the advantage of stable support of the blade. Of course, in general, the opposite method can also be applied.

Numerical control cutting process of thread

(Summary description)The thread cutting process depends on the structure of the machined parts and the CNC machine tool used. Generally speaking, using the right cutting edge to process right-handed threads and using the left cutting edge to process left-handed threads has the advantage of stable support of the blade. Of course, in general, the opposite method can also be applied.

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2021-06-23
  • Views:0

The thread cutting process depends on the structure of the machined parts and the CNC machine tool used. Generally speaking, using the right cutting edge to process right-handed threads and using the left cutting edge to process left-handed threads has the advantage of stable support of the blade. Of course, in general, the opposite method can also be applied.

Is consistent, in order to avoid excessive wear on the side of the blade and shorten the tool life as much as possible.

d2――Pitch diameter A――The blade inclination angle is usually determined by the shim of the indexable thread turning tool. The standard tool is +, but for the internal thread tools with diameters of 16mm and 020mm, there is no shim due to the small space. , So it cannot be processed when the blade inclination is greater than +2°.

The feed method of thread turning is determined by the cutting machine, workpiece material, insert geometry and the pitch of the thread being machined. There are usually the following four feed methods: *Commonly used cutting method, the left and right sides of the turning tool are cut at the same time , The axial cutting component force is offset to some extent, which partially overcomes the phenomenon of turning tool deviation caused by the axial cutting component force. The two sides wear uniformly, which can ensure the clear tooth shape, but there are problems such as poor chip evacuation, poor heat dissipation, and concentrated force. It is suitable for cutting threads with a pitch of less than 1.5mm. D single-side feed cutters feed at an angle with the radial direction. The chips are rolled away from the blade to form strips, which have better heat dissipation. The disadvantage is that the other edge is hardened due to the non-cutting of the friction part. D single-sided infeed direction of 30° angle infeed cutting. The cutting edge cuts on both sides to form rolled chips, smooth chip removal, good heat dissipation, and low thread surface roughness value. Generally speaking, this is the best method for turning stainless steel, alloy steel and carbon steel. About 90% of threaded materials use this method. It is best to use this method for thread processing on a CNC lathe. Generally, a fixed cycle can be called and the programming is simple.

The left and right side feeds alternately cut the left and right sides alternately, that is, each time the radial feed, it moves a certain distance laterally to the left or right, so that only one side of the turning tool participates in the cutting. This method is generally used for general-purpose lathes and thread processing with a medium distance of more than 3mm, and programming on CNC lathes is more complicated.

Thread milling is mainly used for CNC boring and milling machine tools such as machining centers. Generally, small-diameter internal threads (20mm) can be processed by tapping. However, for the processing of large-diameter internal threads and external threads, there are many problems with tapping and sleeve threads. Therefore, medium grain iron cutting is the best processing. means.

Thread milling is different from thread turning plus X. This is because the pattern CNC milling is mainly realized through the three-axis linkage and helical interpolation processing of the machine tool, that is, while the two-axis arc sensitive cutting is processed, the first Three-axis linear feed motion. The axial movement distance is milled. It is a single-edge milling process. Therefore, the best way to feed is to use the radial direct feed cutting method, so that the two cutting edges cut at the same time, and the force is more uniform. , It can ensure the accuracy of the thread, and the CNC programming is relatively simple.

2, the choice of thread turning and milling cutting equipment The choice of thread cutting parameters (cutting speed, back-cutting amount, number of passes) is determined by the material of the tool and the part. The cutting speed of thread turning is generally 25% ~50% lower than that of ordinary turning. The selection of the amount of backing of the thread and the number of passes are also particularly important. Whether the D value is correct or not is directly related to whether the medium pattern is qualified or not. The amount directly affects the size of the cutting force. The amount of the back of the centipede needs to follow the principle of decreasing, that is, the amount of the back of the back of the knife must be less than the amount of the previous one, and the value of the minimum back of the knife is not less than. 5 stomach. The following two tables provide the metric internal and external media pattern backing values. This table is also suitable for thread milling.

Table 1 ISO Metric Pattern Back Knife Setting Value (External Thread) (mm) Pitch Back Knife Cutting Times Flavored Back Knife Quantity Cutting Times Table 2 ISO Metric Pattern Back Knife Setting Value (Internal Thread) Cadmium Back Knife Cutting Times For CNC boring and milling machine tools, although thread milling is realized by three-axis linkage spiral interpolation processing, which is different from thread turning, the choice of cutting quantity can still be used by turning media. The relevant cutting parameters of the pattern. Because the thread milling is made by single-edge cutting, the cutting speed should be half that of turning, and the amount of back-cutting can still be selected according to turning.

3. Thread turning and milling CNC program preparation For CNC lathes, the general standard thread turning programming instructions are G33 (fixed pitch cutting), G34 (variable pitch butterfly cutting with increasing pitch), G35 (variable pitch with decreasing pitch) Thread cutting). The medium distance is specified by / and person ruler, where K /, A: correspond to the X and Z axes respectively. However, general CNC systems and machine tool manufacturers provide thread turning canned cycles for users to use, and only need to input the necessary parameters. H. When processing special butterfly patterns, it is necessary to use the G command and the programming method of calculating the coordinate points by yourself.

   The programming of thread milling processing is different from that of CNC turning. G02 and G03 arc interpolation commands are mainly used, that is, the third axis linear interpolation is added while the two-axis arc interpolation is added to form a spiral interpolation movement. The following is the ordinary internal thread M30X 2, deep 14mm CNC milling processing program , Take the knife back to 1.2mm, adopt the radial direct cutting method.

F200 takes edge compensation, radial feed to the position of the back-grabbing tool. In centuries cutting, it is often due to the correctness of the selection of tools (including inserts, shim and arbor, etc.), feed method, cutting amount, etc. Affects the processing quality of centipede, such as: thread surface has shock marks, surface roughness value is 篼. This may be due to excessive extension of the part or tool, poor rigidity, excessive tool center, and incorrect selection of cutting amount, blade, and sting Caused by other factors. It is possible to increase or decrease the cutting speed, shorten the outer elongation of the tool, adjust the center height or feed method, adopt side feed or radial feed, adequate cooling, increase the number of passes and other solutions.

Fast tool wear and short tool life are caused by too fast cutting speed, insufficient cooling, too many cutting times, and wrong blade grade. It can be used to reduce the cutting speed, fully cooling, reduce the number of cutting, choose the hardness of the wear-resistant blade D with good toughness, change the cutting angle, increase the cooling, increase the cutting speed, reduce the amount of back knife, and adjust the center frame.

The two cutting edges wear unevenly and the feed method, cut corners, Hang Machinery Workers (cold working>Shandong Dongfangyuan Construction Machinery Factory (Haiyang 265100) achieved sales revenue of 296 million yuan in Guobo years. The annual demand for various bearing brackets is very large. , The material is mostly HT200. Among them, the bearing bracket is as shown.

Traditional processing technology process, first scribe the bottom surface, and then process it on the T611 boring machine. During processing, each piece needs to be adjusted, which is troublesome in clamping, time-consuming and labor-intensive, and low efficiency.

Insufficient processing capacity, therefore, we designed a special tooling fixture for turning and boring to produce bearing bracket (H7rr35 with a center height of 257s), which is the main size of the workpiece. Based on this, the design of tooling fixtures is as shown. The jig is used on the CW6263 lathe.

The fixture is composed of a main body 3 and a three-jaw self-centering chuck 4. Remove one claw of the three-jaw self-centering chuck. The left end of the main body 3 is connected with the chuck and fastened with bolt 1. The A side table is placed on the positioning surface of the bearing bracket. The main body has two notches for the free movement of the claws. s First, ensure the center of the bearing bracket 5, and then use the three-claw self-selection due to improper selection, to change the feed method and cut corners.

The built-up edge on the cutting edge increases the cutting speed and increases the cooling. It uses coated carbide inserts and adopts improved side feed cutting.

Excessive plastic deformation of the tool is caused by poor cooling, too high cutting speed, incorrect blade grade, and too much back-grabbing each time. Should reduce the amount of back-grabbing, increase cooling, reduce cutting speed, increase cutting times, use high hardness, wear-resistant hard alloy or Xu layer blades.

There is a burr on the top of the thread. To increase the cutting speed, use the automatic centering principle with the cutting centering chuck 4 to clamp the workpiece for processing.

Then tighten the chuck to clamp the workpiece.

Using the car to replace the collision completely meets the design requirements of the bearing bracket, guarantees the dimensional accuracy and position accuracy, and saves the workpiece scribing and correction, guarantees the quality, and improves the work efficiency by 1.8 times compared with the boring process.

Bearing brackets with different center heights can be adjusted by adding shims, but they need to be fastened by bolts.

Balance adjustment is required before use to avoid the influence of centrifugal force on the quality of the workpiece and the pressure plate on the equipment.

The size of each part of the main body can be determined according to the size of the bearing bracket. The book is edited by China National Machine Tool Corporation Beijing National Machinery Exhibition Center. It gathers products from more than 500 companies, 1717 pages, 16 format, two volumes, including: Volume 1: Metal cutting Machine tools; Volume II: Forging machinery, foundry machinery, woodworking machinery, blades attached to machine tools.

numerical control system and machine tool electrical appliances, etc. The price is 350 yuan (including post and chip removal is not easy to control, reduce the cutting speed, adjust the feed method, adopt improved side feed cutting, and increase cooling.

News

On

On the occasion of the New Year, I wish all the new and old customers a happy, happy and long career, good luck in the year of the pig!

On the occasion of the New Year, I wish all the new and old customers a happy, happy and long career, good luck in the year of the pig!
2019-02-01
CCMT2016

CCMT2016

China CNC Machine Tool Fair(CCMT)was initiated in Shanghai in 2000 and has been successfully held for 8 sessions, 5 were held in Shanghai, 1 in Beijing and 2 in Nanjing. For long-term development and providing a larger platform to exhibitors, CCMT move back to Shanghai in 2014 and will be fixed in Shanghai forever. Based in South China,CCMT echoes with CIMT in North China,and will provide more vast space to exhibitors from both home and abroad.CCMT is the sister show of CIMT which is the most authoritative machine tool show in China,and now it plays more and more strong influence on the machine tool industry and its users.
2018-08-16
The

The characteristics of nc tool compared with ordinary machine tools

CIMT2017 will be held at the New International Exhibition Center in Beijing, China from April 17-22. The China International Machine Tool Show (CIMT) was founded in 1989 by the China Machine Tool Industry Association. It is held every single year. It is the most prestigious international machine tool exhibition in China.
2018-08-16
Simple

Simple troubleshooting CNC tools

As a result of the CNC tool machine tool transmission chain mostly adopts rolling friction pair, so the fault mostly cause for the quality decline of movement.
2018-08-16

Zhejiang Yinqiu Machinery Co., Ltd.

The only thing we can give back to our valued customers is to do our best

Zhejiang Yinqiu Machinery Co., Ltd.
TOP

Zhejiang Yinqiu Machinery Co., Ltd. 

We are a comprehensive technology-based enterprise covering intelligent equipment manufacturing and machine tool precision tools.

Contact us

Address: 1 hongqi road, xinchang industrial park, xinchang county, zhejiang province
Machine tool accessories:
0575-86590918
Mobile phone:15215987912Mr wu   15167531088Mr liu
Intelligent tea making machine:
0575-86097099 
Mobile phone:
13506752882Mr zhao   18957565808Mr zhou
Fax:
0575-86590918
QQ: 2818242396
E-mail:
info@yqzentax.com

搜索
Search

© 2021 Zhejiang Yinqiu Machinery Co., Ltd.   |   浙ICP备06013885号-2   |    Powered by www.300.cn 

Zhejiang Yinqiu Machinery Co., Ltd.